前書き
圧力は、工業生産における重要なプロセスパラメータの1つです。 圧力が要件を満たさない場合、生産効率に影響を与えるだけでなく、製品の品質を低下させるだけでなく、重大な安全事故を引き起こすことさえあります。 したがって、圧力測定は工業生産において特別なステータスを持っています。 この記事では、圧力計の選択、設置、校正をそれぞれ紹介します。
まず、圧力計の選択
製品プロセス要件に応じた機器タイプの正しい選択は、機器の正常な動作と安全な生産を保証するための重要な前提条件です。 一般に、機器の種類を選択する際には、次の3つの要件を考慮する必要があります。(1)工業生産における製品プロセスの要件に従って選択します。 たとえば、リモート送信、自動記録、またはアラームが必要かどうか。 (2)測定された媒体の物理的および化学的性質による。 腐食性、温度、粘度、汚染の程度、可燃性および爆発性など、測定器が選択する特別な要件を提示するかどうか。 (3)オン-サイトの環境条件による。 高温、電磁界、振動、現場での設置条件など、機器の種類に特別な要件があるかどうかなど。
1.測定器の測定範囲の決定
計測器を合理的かつ経済的に使用するために、計測器の範囲を大きくしすぎることはできませんが、測定精度を確保するために、測定圧力の最小値は、通常、フルスケールの1/3以上です。楽器。 弾性要素は、長時間の過度の応力により永久に変形します。 圧力計の上限は、測定する最大値(範囲の1/21/3)より高くし、マージンを確保する必要があります。
2.計測器の精度の選択
The accuracy of the instrument is determined according to the maximum measurement error allowed in the production process. It cannot be considered that the higher the accuracy of the instrument, the better. On the premise of meeting the process requirements, the instrument with lower precision, low price and durability should be selected as much as possible. Example of instrument type selection: The outlet pressure range of a compressor is 25~28MPa, and the absolute measurement error should not be greater than 1MPa. The process requires on-site observation and high and low limit alarms. Try to choose a pressure gauge correctly, and point out the model, accuracy and measurement range. The required conditions are: the measured pulsating pressure is 25~28MPa, and the absolute measurement error is less than or equal to 1MPa. Observation, high and low limit alarm. When selecting the instrument, consider that the pulsating pressure has a great influence on the life of the instrument, so the upper limit of the instrument selected is: P1=Pmax*2=28*2=56MPa. If the measurement range of the pressure gauge is 0~60MPa, then: 25MPa/60MPa>1/3、測定圧力の最小値はフルスケールの1/3以上であり、下限値も要件を満たしています。 さらに、測定誤差の要件に従って、測定器の許容誤差の要件は次のように計算できます:1/60100パーセント=1。67パーセント、したがって、精度レベル1.5の測定器はエラー要件を満たします。
2番目。 圧力計の設置
Whether the pressure gauge is installed correctly or not directly affects the accuracy of the measurement results and the service life of the pressure gauge. The key to the installation of the pressure gauge is the selection of the pressure measuring point: (1) The pressure measuring point should be selected where the measured medium flows in a straight line. For the pipe segment, do not select it at the bend, bifurcation or dead end of the pipeline. (2) When measuring the liquid pressure, the pressure point should be perpendicular to the flow direction, the inner end face of the pressure pipe should be flush with the inner wall of the equipment, and there should be no protrusions or burrs. (3) When measuring the liquid pressure, the pressure-taking point should be at the lower part of the pipeline, so that no gas is accumulated in the pressure-guiding pipe; when measuring the gas pressure, the pressure-taking point should be above the pipe, so that no liquid is accumulated in the pressure-guiding pipe. (4) A shut-off
3日。 圧力(差圧)検出器の検証と校正
機器を使用する前に、検証と校正を行う必要があります。 長期間使用する機器も定期的にチェックし、使用頻度や強調度に応じてサイクルを決定する必要があります。 計器に長距離-距離伝送システムと二次計器がある場合は、二次計器と一緒に検証および校正する必要があります。 圧力計の校正方法は次のとおりです。標準の圧力計を使用して校正します。






